Harware: HP xw8600 2x Xeon 5470 3.33ghz 32 GB ram
BIOS Configuration: Hewlett-Packard 786F5 v01.46 09/20/2012
HARD DRIVES:
2 wd 750 GB HDD
2 wd black 1 tb HDD
2 Seagate 3 TB HDD
Each set is a mirrored pair.
When I installed the 3 tb disks the bios showed only 801 GB. I tried a few setting chngs but cannot report
exactly what they were... didn't record them, but at any rate BIOS still showed and now shows 801 GB for those
Drives.
However when I boot the OS (a developement branch of solaris 11 called openindiana/hipster with illumos software.)
The OS appears to recognize the full size of the disks and reports 2.73 TB (some is used for the OS)
I've put data on the mirrored pair of 3 TB discs... only about 350 GB so far.
However on reboot I see a message flash by that I haven't been able to record but one part I have caught
says the `Hardware does not support' those 3 TB disks.
Further, at least dozens and probably 100s of lines of this format:
read DDD (D for digit) at least 225 so
read 225 from 5060511486 to 0xce8c5a60, error: 0x1
The Hex and Decimal numbers change as a progression from smaller to larger, for each line.
but not the ending `0x1'.
I don't know what it means but it happens on every reboot... however once the OS comes up I see the discs
reported at the right size and the data seems to be sound.
Are there any settings I can tinker with that might help?
What follows if from an OS tool called prtdiag just a more definitive report on the
hardware (Not the disks) and after that a the output of `format' cmd that does show the disks
Output of prtdiag
System Configuration: Hewlett-Packard HP xw8600 Workstation
BIOS Configuration: Hewlett-Packard 786F5 v01.46 09/20/2012
==== Processor Sockets ====================================
Version Location Tag
-------------------------------- --------------------------
Intel(R) Xeon(R) CPU X5470 @ 3.33GHz XU1 PROCESSOR
Intel(R) Xeon(R) CPU X5470 @ 3.33GHz XU2 PROCESSOR
==== Memory Device Sockets ================================
Type Status Set Device Locator Bank Locator
----------- ------ --- ------------------- ----------------
DDR2 FBDIMM in use 1 DIMM01
DDR2 FBDIMM in use 3 DIMM02
DDR2 FBDIMM in use 1 DIMM03
DDR2 FBDIMM in use 3 DIMM04
DDR2 FBDIMM in use 2 DIMM05
DDR2 FBDIMM in use 4 DIMM06
DDR2 FBDIMM in use 2 DIMM07
DDR2 FBDIMM in use 4 DIMM08
FLASH in use 0 SYSTEM ROM
==== On-Board Devices =====================================
==== Upgradeable Slots ====================================
ID Status Type Description
--- --------- ---------------- ----------------------------
1 available PCI SLOT 1 PCI
2 in use PCI Express SLOT 2 PCIe x16
3 available PCI Express SLOT 3 PCIe x8 (4)
4 available PCI Express SLOT 4 PCIe x16 or x8
3 available PCI Express SLOT 5 PCIe x1 or x8
3 available PCI Express SLOT 6 PCIe x8 (4)
5 available PCI-X SLOT 7 PCI-X 133
===================================================
OUTPUT of `format'
===================================================
AVAILABLE DISK SELECTIONS:
0. c3t6d0 <WDC-WD1003FZEX-00MK2A0-01.01A01-931.51GB>
/pci@0,0/pci8086,4029@9/pci8086,350c@0,3/pci103c,a98@6/sd@6,0
1. c3t7d0 <WDC-WD1003FZEX-00MK2A0-01.01A01-931.51GB>
/pci@0,0/pci8086,4029@9/pci8086,350c@0,3/pci103c,a98@6/sd@7,0
2. c5d0 <Unknown-Unknown-0001 cyl 45597 alt 2 hd 255 sec 126>
/pci@0,0/pci-ide@1f,2/ide@0/cmdk@0,0
3. c5d1 <WDC WD7501AALS-00J7B0= WD-WMATV0120915- WD-WMATV0120915-0001-698.63GB>
/pci@0,0/pci-ide@1f,2/ide@0/cmdk@1,0
4. c6d0 <ST33000651NS= Z2946BL1- Z2946BL1-0001-2.73TB>
/pci@0,0/pci-ide@1f,2/ide@1/cmdk@0,0
5. c6d1 <ST33000651NS= Z2949YSM- Z2949YSM-0001-2.73TB>
/pci@0,0/pci-ide@1f,2/ide@1/cmdk@1,0
The last two:
4. c6d0
5. c6d1
Are the 3tb discs shown as 2.73 TB